Pim Valid

Description Power The Vcc signal is the power supply to the device. Reserved / Power The host shall always provide Vcc on these pins. The device shall tolerate Vcc on these pins but is not required to draw power from them. Ground The Vss signal is the power supply ground. Reserved / Ground The host shall always provide Vss on these pins. The device shall tolerate Vss on these pins but is not required to use them. Command Latch Enable The Command Latch Enable signal loads a command into…

. . . . . . . PIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring Virtual IP Support for VRRP. . . . . . . . . . . . . . . . . . PIM Support for IP Clustering . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring Dense-Mode PIM . . . . . . . . . . . . . . . . . . . . . . . . . . Disabling PIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting Advanced Options for Dense-Mode PIM (Optional) . .

Programmable code protection • Power saving SLEEP mode • Selectable oscillator options • Low power, high speed CMOS FLASH/EEPROM technology • Fully static design • In-Circuit Serial Programming (ICSP) via two pins • Single 5V In-Circuit Serial Programming capability • In-Circuit Debugging via two pins • Processor read/write access to program memory • Wide operating voltage range: 2.0V to 5.5V • High Sink/Source Current: 25 mA • Commercial and Industrial temperature ranges • Low power…

PARANÁ A descrição abaixo resume algumas características do Seeeduino.  Microcontroller ATmega168  Operating Voltage 5V/3.3V  Input Voltage (recommended) 7-12 V  Input Voltage (limits) 6-20 V  Digital I/O Pins 14 (of which 6 provide PWM output)  Analog Input Pins 8  DC Current per I/O Pin 40 mA  DC Current for 3.3V Pin 50 mA  Flash Memory 16 KB (of which 2 KB used by boot loader)  SRAM 1 KB  EEPROM 512 bytes  Clock Speed 16 MHz O Seeduino vem gravado…

User Manual UP Teton 1 UP Teton User Manual Version 1.0 Valid from production year 2003 Date: 01.03.2004 2 The data and statements contained within this manual may be changed without prior notice. No part of these documents may be copied or transmitted for any purpose in any manner or by any means, either electronic or mechanical, without explicit written permission from Ultralite Products Europe. © 1995-2004 Ultralite Products Europe 3 Table of contents WELCOME IN

(continues on pages 26 to 26) LED Channels Status Type Telephone Interface Color State Blinking Fast Blinking Off On Definition The phone is ringing (incoming call, before answering). Line malfunction Normal onhook position Offhook Ringing Valid 10/100 Base-TX Ethernet connection No uplink Failure (fatal error). Or system initialization. Normal working condition Device powered, self-test OK Software loading or System failure Power iscurrently being supplied to the device…

|MDA 01 |Support for PIM |Support of at least one PIM (Generic UML and domain-tagged UML profiles can be | | | |considered PIM) | | | |Support Multiple Viewpoint PIM | | | |PIM extensibility…

Agripec Química e Farmacêutica S.A. Projeto Integrado Multidisciplinar (PIM), apresentado com exigência parcial para conclusão do 5° semestre do curso superior de formação Tecnológica – Processos Gerenciais da Universidade Paulista (UNIP), campus São Caetano do Sul sob orientação da professora Angela Maria Pizzo. SÃO CAETANO DO SUL - SP 2012 RESUMO Para o desenvolvimento do presente Projeto Integrado Multidisciplinar – PIM V foi escolhida a organização Agripec Química e…

register (GPIOx_LCKR) (x=A..G) . . . . . . . . . . 113 7.3 Alternate function I/O and debug configuration (AFIO) . . . . . . . . . . . . . 114 7.3.1 7.3.2 7.3.3 7.3.4 7.3.5 7.3.6 7.3.7 7.3.8 Using OSC32_IN/OSC32_OUT pins as GPIO ports PC14/PC15 . . . . 114 Using OSC_IN/OSC_OUT pins as GPIO ports PD0/PD1 . . . . . . . . . . 114 JTAG/SWD alternate function remapping . . . . . . . . . . . . . . . . . . . . . . 115 Timer alternate function remapping . . . . . . . . . . . . . . . . . .…

current from each output port pin. This current is usually sufficient to drive LEDs, small lamps, buzzers, small relays, etc. The current capability can be increased by connecting external transistor switching circuits or relays to the output port pins. Microcontroller systems 11 1.4 Microcontroller architectures Usually two types of architectures are used in microcontrollers (see Figure 1.6): Von Neumann architecture and Harvard architecture. Von Neumann architecture is…